[ 105.547529] c0 usb 1-2: New USB device found, idVendor=05c6, idProduct=9008 [ 105.547694] c0 usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 105.547862] c0 usb 1-2: Product: QHSUSB__BULK [ 105.547975] c0 usb 1-2: Manufacturer: Qualcomm CDMA Technologies MSM [ 105.548123] c0 call_battery_notify : VID : 0x5c6, PID : 0x9008 skipped. [ 105.565375] c0 usb 1-2: usb_probe_device [ 105.565508] c0 usb 1-2: configuration #1 chosen from 1 choice [ 105.566040] c0 usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 105.570614] c0 qcserial 1-2:1.0: usb_probe_interface [ 105.570757] c0 qcserial 1-2:1.0: usb_probe_interface - got id [ 105.570938] c0 check_chip_configuration: usb product name = QHSUSB__BULK [ 105.571091] c0 mdm9x15 boot protocol = SAHARA [ 105.571211] c0 qcserial 1-2:1.0: Qualcomm USB modem converter detected [ 105.582477] c0 usb 1-2: Qualcomm USB modem converter now attached to ttyUSB0 [ 105.890809] c0 mdm_modem_ioctl: mdm get boot protocol 0 [ 106.270120] c0 s5p-ohci s5p-ohci: auto-stop root hub [ 107.525186] c0 hub 2-0:1.0: hub_suspend [ 107.525334] c0 usb usb2: bus auto-suspend [ 107.525440] c0 s5p-ohci s5p-ohci: suspend root hub [ 110.701341] c0 mdm_modem_ioctl: check if mdm is booted up [ 110.701443] c0 mdm_modem_ioctl: normal boot done [ 110.701529] c0 normal_boot_done [ 110.701589] c0 mdm_peripheral_disconnect [ 110.701962] c0 s5p-ohci s5p-ohci: remove, state 4 [ 110.702087] c0 s5p-ohci s5p-ohci: roothub graceful disconnect [ 110.702242] c0 usb usb2: USB disconnect, device number 1 by usb_remove_hcd+0xc8/0x168 [ 110.702378] c0 call_battery_notify : VID : 0x1d6b, PID : 0x1 skipped. [ 110.702490] c0 usb usb2: unregistering device [ 110.702573] c0 usb usb2: unregistering interface 2-0:1.0 [ 110.704414] c0 usb usb2: usb_disable_device nuking all URBs [ 110.718730] c0 s5p-ohci s5p-ohci: OHCI controller state [ 110.718836] c0 s5p-ohci s5p-ohci: OHCI 1.0, NO legacy support registers [ 110.718958] c0 s5p-ohci s5p-ohci: control 0x4c3 RWE HCFS=suspend CBSR=3 [ 110.719076] c0 s5p-ohci s5p-ohci: cmdstatus 0x00000 SOC=0 [ 110.719178] c0 s5p-ohci s5p-ohci: intrstatus 0x00000004 SF [ 110.719278] c0 s5p-ohci s5p-ohci: intrenable 0x0000005a RHSC UE RD WDH [ 110.719396] c0 s5p-ohci s5p-ohci: hcca frame #044d [ 110.719493] c0 s5p-ohci s5p-ohci: roothub.a 02000203 POTPGT=2 NPS NDP=3(3) [ 110.719613] c0 s5p-ohci s5p-ohci: roothub.b 00000000 PPCM=0000 DR=0000 [ 110.719727] c0 s5p-ohci s5p-ohci: roothub.status 00008000 DRWE [ 110.719835] c0 s5p-ohci s5p-ohci: roothub.portstatus [0] 0x00000100 PPS [ 110.719953] c0 s5p-ohci s5p-ohci: roothub.portstatus [1] 0x00000100 PPS [ 110.720202] c0 s5p-ohci s5p-ohci: roothub.portstatus [2] 0x00000100 PPS [ 110.720508] c0 s5p-ohci s5p-ohci: USB bus 2 deregistered [ 110.724454] c0 s5p-ohci s5p-ohci: still being used(18) [ 110.725876] c0 s5p-ehci s5p-ehci: remove, state 1 [ 110.725992] c0 s5p-ehci s5p-ehci: roothub graceful disconnect [ 110.726145] c0 usb usb1: USB disconnect, device number 1 by usb_remove_hcd+0xc8/0x168 [ 110.726280] c0 call_battery_notify : VID : 0x1d6b, PID : 0x2 skipped. [ 110.726404] c0 usb 1-2: USB disconnect, device number 2 by usb_disconnect+0xa0/0x18c [ 110.726535] c0 call_battery_notify : VID : 0x5c6, PID : 0x9008 skipped. [ 110.726648] c0 usb 1-2: unregistering device [ 110.726728] c0 usb 1-2: unregistering interface 1-2:1.0 [ 110.728960] c0 qcserial ttyUSB0: Qualcomm USB modem converter now disconnected from ttyUSB0 [ 110.729898] c0 qcserial 1-2:1.0: device disconnected [ 110.731062] c0 usb 1-2: usb_disable_device nuking all URBs [ 110.735016] c0 usb usb1: unregistering device [ 110.735286] c0 usb usb1: unregistering interface 1-0:1.0 [ 110.735645] c0 s5p-ehci s5p-ehci: shutdown urb e88f5d00 ep1in-intr [ 110.736783] c0 usb usb1: usb_disable_device nuking all URBs [ 110.748031] c0 s5p-ehci s5p-ehci: stop [ 110.748296] c0 s5p-ehci s5p-ehci: reset command 0010006 (park)=0 ithresh=1 period=512 Reset HALT [ 110.750497] c0 s5p-ehci s5p-ehci: irq normal 961 err 11 reclaim 202 (lost 0) [ 110.750620] c0 s5p-ehci s5p-ehci: complete 992 unlink 1 [ 110.750722] c0 s5p-ehci s5p-ehci: ehci_stop completed status 1000 Halt [ 110.750877] c0 s5p-ehci s5p-ehci: USB bus 1 deregistered [ 110.753227] c0 s5p-ehci s5p-ehci: still being used(16) [ 110.755806] c0 mdm_modem_ioctl: wait for mdm to need images reloaded [ 111.379250] c0 mdm_status_change: status = 1: mdm is now ready [ 111.379476] c0 mdm_peripheral_disconnect [ 111.379585] c0 mdm_peripheral_connect [ 111.386542] c0 set hsic lpa phy init [ 111.386669] c0 s5p-ehci s5p-ehci: usb phy usage(18) [ 111.386791] c0 s5p-ehci s5p-ehci: Already power on PHY [ 111.386920] c0 usb: set_exynos_usb_phy_tune old phy1 tune=0x2831b3 t=1 [ 111.387082] c0 usb: set_exynos_usb_phy_tune new phy1 tune=0x2831b3 [ 111.387238] c0 s5p-ehci s5p-ehci: s5p_ehci_phy_init : 0x3c00000 [ 111.387398] c0 s5p-ehci s5p-ehci: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3 [ 111.387597] c0 s5p-ehci s5p-ehci: reset hcc_params 2a016 thresh 1 uframes 256/512/1024 park LPM [ 111.387788] c0 s5p-ehci s5p-ehci: S5P EHCI Host Controller [ 111.392245] c0 s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1 [ 111.392750] c0 s5p-ehci s5p-ehci: park 0 [ 111.392857] c0 s5p-ehci s5p-ehci: support lpm [ 111.393054] c0 s5p-ehci s5p-ehci: irq 134, io mem 0x12580000 [ 111.393227] c0 s5p-ehci s5p-ehci: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT [ 111.393454] c0 s5p-ehci s5p-ehci: init command 0010005 (park)=0 ithresh=1 period=512 RUN [ 111.400267] c0 s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00 [ 111.400850] c0 usb usb1: default language 0x0409 [ 111.401059] c0 usb usb1: udev 1, busnum 1, minor = 0 [ 111.401189] c0 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 111.401354] c0 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 111.401520] c0 usb usb1: Product: S5P EHCI Host Controller [ 111.401649] c0 usb usb1: Manufacturer: Linux 3.0.101-replicant ehci_hcd [ 111.401798] c0 usb usb1: SerialNumber: s5p-ehci [ 111.401915] c0 call_battery_notify : VID : 0x1d6b, PID : 0x2 skipped. [ 111.415217] c0 usb usb1: usb_probe_device [ 111.415351] c0 usb usb1: configuration #1 chosen from 1 choice [ 111.415592] c0 usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 111.419411] c0 hub 1-0:1.0: usb_probe_interface [ 111.419536] c0 hub 1-0:1.0: usb_probe_interface - got id [ 111.419680] c0 hub 1-0:1.0: USB hub found [ 111.419840] c0 hub 1-0:1.0: 3 ports detected [ 111.419951] c0 hub 1-0:1.0: standalone hub [ 111.420260] c0 hub 1-0:1.0: individual port power switching [ 111.420398] c0 hub 1-0:1.0: individual port over-current protection [ 111.420546] c0 hub 1-0:1.0: power on to power good time: 20ms [ 111.420739] c0 hub 1-0:1.0: local power source is good [ 111.420867] c0 hub 1-0:1.0: enabling power on all ports [ 111.425481] c0 dev rdy val = 0 [ 111.425575] c0 set_host_stat:set host port power status to [1] [ 111.429716] c0 s5p-ohci s5p-ohci: usb phy usage(22) [ 111.429846] c0 s5p-ohci s5p-ohci: Already power on PHY [ 111.429975] c0 usb: set_exynos_usb_phy_tune old phy1 tune=0x2831b3 t=1 [ 111.430322] c0 usb: set_exynos_usb_phy_tune new phy1 tune=0x2831b3 [ 111.430474] c0 s5p-ohci s5p-ohci: s5p OHCI [ 111.434445] c0 s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2 [ 111.434665] c0 s5p-ohci s5p-ohci: ohci_s5p_init, ohci:e708e908 [ 111.435348] c0 s5p-ohci s5p-ohci: created debug files [ 111.435553] c0 s5p-ohci s5p-ohci: irq 134, io mem 0x12590000 [ 111.435692] c0 s5p-ohci s5p-ohci: ohci_s5p_start, ohci:e708e908 [ 111.494159] c0 s5p-ohci s5p-ohci: OHCI controller state [ 111.494307] c0 s5p-ohci s5p-ohci: OHCI 1.0, NO legacy support registers [ 111.494478] c0 s5p-ohci s5p-ohci: control 0x083 HCFS=operational CBSR=3 [ 111.494638] c0 s5p-ohci s5p-ohci: cmdstatus 0x00000 SOC=0 [ 111.494779] c0 s5p-ohci s5p-ohci: intrstatus 0x00000004 SF [ 111.494922] c0 s5p-ohci s5p-ohci: intrenable 0x8000005a MIE RHSC UE RD WDH [ 111.495190] c0 s5p-ohci s5p-ohci: hcca frame #0006 [ 111.495330] c0 s5p-ohci s5p-ohci: roothub.a 02000203 POTPGT=2 NPS NDP=3(3) [ 111.495493] c0 s5p-ohci s5p-ohci: roothub.b 00000000 PPCM=0000 DR=0000 [ 111.495649] c0 s5p-ohci s5p-ohci: roothub.status 00008000 DRWE [ 111.495799] c0 s5p-ohci s5p-ohci: roothub.portstatus [0] 0x00000100 PPS [ 111.495961] c0 s5p-ohci s5p-ohci: roothub.portstatus [1] 0x00000100 PPS [ 111.496121] c0 s5p-ohci s5p-ohci: roothub.portstatus [2] 0x00000100 PPS [ 111.496432] c0 usb usb2: default language 0x0409 [ 111.496634] c0 usb usb2: udev 1, busnum 2, minor = 128 [ 111.496764] c0 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 111.496929] c0 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 111.497095] c0 usb usb2: Product: s5p OHCI [ 111.497200] c0 usb usb2: Manufacturer: Linux 3.0.101-replicant ohci_hcd [ 111.497350] c0 usb usb2: SerialNumber: s5p-ohci [ 111.497467] c0 call_battery_notify : VID : 0x1d6b, PID : 0x1 skipped. [ 111.507573] c0 usb usb2: usb_probe_device [ 111.507700] c0 usb usb2: configuration #1 chosen from 1 choice [ 111.507937] c0 usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 111.511851] c0 hub 2-0:1.0: usb_probe_interface [ 111.511974] c0 hub 2-0:1.0: usb_probe_interface - got id [ 111.512117] c0 hub 2-0:1.0: USB hub found [ 111.512269] c0 hub 2-0:1.0: 3 ports detected [ 111.512379] c0 hub 2-0:1.0: standalone hub [ 111.512482] c0 hub 2-0:1.0: no power switching (usb 1.0) [ 111.512605] c0 hub 2-0:1.0: global over-current protection [ 111.512737] c0 hub 2-0:1.0: power on to power good time: 4ms [ 111.512919] c0 hub 2-0:1.0: local power source is good [ 111.513043] c0 hub 2-0:1.0: no over-current condition exists [ 111.513178] c0 hub 2-0:1.0: trying to enable port power on non-switchable hub [ 111.520394] c0 s5p-ehci s5p-ehci: GetStatus port:2 status 001803 0 ACK POWER sig=j CSC CONNECT [ 111.520615] c0 hub 1-0:1.0: port 2: status 0501 change 0001 [ 111.523617] c0 request_boot_lock_release [ 111.523735] c0 request_active_lock_set [ 111.610199] c0 hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 [ 111.620171] c0 hub 1-0:1.0: state 7 ports 3 chg 0004 evt 0000 [ 111.620304] c0 hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 111.675182] c0 s5p-ehci s5p-ehci: port 2 high speed [ 111.675289] c0 s5p-ehci s5p-ehci: GetStatus port:2 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 111.730121] c0 usb 1-2: new high speed USB device number 2 using s5p-ehci [ 111.785320] c0 s5p-ehci s5p-ehci: port 2 high speed [ 111.785480] c0 s5p-ehci s5p-ehci: GetStatus port:2 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 111.860890] c0 usb 1-2: USB quirks for this device: 600 [ 111.863155] c0 usb 1-2: default language 0x0409 [ 111.864299] c0 usb 1-2: udev 2, busnum 1, minor = 1 [ 111.864456] c0 usb 1-2: New USB device found, idVendor=05c6, idProduct=904c [ 111.864623] c0 usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0 [ 111.864792] c0 usb 1-2: Product: Qualcomm CDMA Technologies MSM [ 111.864935] c0 usb 1-2: Manufacturer: Qualcomm, Incorporated [ 111.865176] c0 call_battery_notify : VID : 0x5c6, PID : 0x904c skipped. [ 111.874881] c0 usb 1-2: usb_probe_device [ 111.875013] c0 usb 1-2: configuration #1 chosen from 1 choice [ 111.881176] c0 usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 111.885011] c0 qmi_wwan 1-2:1.0: usb_probe_interface [ 111.885354] c0 qmi_wwan 1-2:1.0: usb_probe_interface - got id [ 111.885509] c0 qmi_wwan 1-2:1.0: not blacklisted [ 111.887265] c0 qmi_wwan 1-2:1.0: bind didnt work [ 111.887508] c0 qmi_wwan: probe of 1-2:1.0 failed with error -22 [ 111.887717] c0 rmnet_usb 1-2:1.0: usb_probe_interface [ 111.887848] c0 rmnet_usb 1-2:1.0: usb_probe_interface - got id [ 111.887993] c0 usb 1-2: rmnet usb probe [ 111.888096] c0 usb 1-2: testbit failed [ 111.888316] c0 cdc_wdm 1-2:1.0: usb_probe_interface [ 111.888442] c0 cdc_wdm 1-2:1.0: usb_probe_interface - got id [ 111.888624] c0 cdc_wdm: probe of 1-2:1.0 failed with error -22 [ 111.888931] c0 qcserial 1-2:1.0: usb_probe_interface [ 111.889075] c0 qcserial 1-2:1.0: usb_probe_interface - got id [ 111.889384] c0 diag_bridge 1-2:1.0: usb_probe_interface [ 111.889516] c0 diag_bridge 1-2:1.0: usb_probe_interface - got id [ 111.889666] c0 /home/wolfi/replicant/6.0-romsrc/kernel/samsung/smdk4412/drivers/usb/misc/diag_bridge.c: diag_bridge_probe: id:0 [ 111.893977] c0 usb 1-2: diag_bridge_probe: complete [ 111.894157] c0 usb 1-2: adding 1-2:1.1 (config #1, interface 1) [ 111.898143] c0 qmi_wwan 1-2:1.1: usb_probe_interface [ 111.898286] c0 qmi_wwan 1-2:1.1: usb_probe_interface - got id [ 111.898434] c0 qmi_wwan 1-2:1.1: not blacklisted [ 111.900475] c0 qmi_wwan 1-2:1.1: bind didnt work [ 111.900700] c0 qmi_wwan: probe of 1-2:1.1 failed with error -22 [ 111.900909] c0 rmnet_usb 1-2:1.1: usb_probe_interface [ 111.901037] c0 rmnet_usb 1-2:1.1: usb_probe_interface - got id [ 111.901184] c0 usb 1-2: rmnet usb probe [ 111.901283] c0 usb 1-2: testbit failed [ 111.901497] c0 cdc_wdm 1-2:1.1: usb_probe_interface [ 111.901625] c0 cdc_wdm 1-2:1.1: usb_probe_interface - got id [ 111.901803] c0 cdc_wdm: probe of 1-2:1.1 failed with error -22 [ 111.902109] c0 qcserial 1-2:1.1: usb_probe_interface [ 111.902251] c0 qcserial 1-2:1.1: usb_probe_interface - got id [ 111.902548] c0 diag_bridge 1-2:1.1: usb_probe_interface [ 111.902680] c0 diag_bridge 1-2:1.1: usb_probe_interface - got id [ 111.902830] c0 /home/wolfi/replicant/6.0-romsrc/kernel/samsung/smdk4412/drivers/usb/misc/diag_bridge.c: diag_bridge_probe: id:0 [ 111.903166] c0 mdm_bridge 1-2:1.1: usb_probe_interface [ 111.903296] c0 mdm_bridge 1-2:1.1: usb_probe_interface - got id [ 111.903564] c0 usb 1-2: adding 1-2:1.2 (config #1, interface 2) [ 111.910601] c0 qmi_wwan 1-2:1.2: usb_probe_interface [ 111.910746] c0 qmi_wwan 1-2:1.2: usb_probe_interface - got id [ 111.910893] c0 qmi_wwan 1-2:1.2: not blacklisted [ 111.912666] c0 qmi_wwan 1-2:1.2: bind didnt work [ 111.912883] c0 qmi_wwan: probe of 1-2:1.2 failed with error -22 [ 111.913094] c0 rmnet_usb 1-2:1.2: usb_probe_interface [ 111.913227] c0 rmnet_usb 1-2:1.2: usb_probe_interface - got id [ 111.913371] c0 usb 1-2: rmnet usb probe [ 111.913470] c0 usb 1-2: testbit failed [ 111.913686] c0 cdc_wdm 1-2:1.2: usb_probe_interface [ 111.913813] c0 cdc_wdm 1-2:1.2: usb_probe_interface - got id [ 111.913994] c0 cdc_wdm: probe of 1-2:1.2 failed with error -22 [ 111.914295] c0 qcserial 1-2:1.2: usb_probe_interface [ 111.914439] c0 qcserial 1-2:1.2: usb_probe_interface - got id [ 111.914632] c0 qcserial 1-2:1.2: Qualcomm USB modem converter detected [ 111.927835] c0 usb 1-2: Qualcomm USB modem converter now attached to ttyUSB0 [ 111.928083] c0 usb 1-2: adding 1-2:1.3 (config #1, interface 3) [ 111.932900] c0 qmi_wwan 1-2:1.3: usb_probe_interface [ 111.933004] c0 qmi_wwan 1-2:1.3: usb_probe_interface - got id [ 111.933113] c0 qmi_wwan 1-2:1.3: not blacklisted [ 111.940371] c0 qmi_wwan 1-2:1.3: looking for a minor, starting at 176 [ 111.944233] c0 qmi_wwan 1-2:1.3: cdc-wdm0: USB WDM device [ 111.960427] c0 qmi_wwan 1-2:1.3: wwan0: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 111.960676] c0 usb 1-2: adding 1-2:1.4 (config #1, interface 4) [ 111.963043] c0 qmi_wwan 1-2:1.4: usb_probe_interface [ 111.963151] c0 qmi_wwan 1-2:1.4: usb_probe_interface - got id [ 111.963261] c0 qmi_wwan 1-2:1.4: not blacklisted [ 111.965553] c0 qmi_wwan 1-2:1.4: looking for a minor, starting at 176 [ 111.970392] c0 qmi_wwan 1-2:1.4: cdc-wdm1: USB WDM device [ 111.986045] c0 qmi_wwan 1-2:1.4: wwan1: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 111.986296] c0 usb 1-2: adding 1-2:1.5 (config #1, interface 5) [ 111.990489] c0 qmi_wwan 1-2:1.5: usb_probe_interface [ 111.990595] c0 qmi_wwan 1-2:1.5: usb_probe_interface - got id [ 111.990704] c0 qmi_wwan 1-2:1.5: not blacklisted [ 111.992212] c0 qmi_wwan 1-2:1.5: looking for a minor, starting at 176 [ 111.998524] c0 qmi_wwan 1-2:1.5: cdc-wdm2: USB WDM device [ 112.015019] c0 qmi_wwan 1-2:1.5: wwan2: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 112.015426] c0 usb 1-2: adding 1-2:1.6 (config #1, interface 6) [ 112.017656] c0 qmi_wwan 1-2:1.6: usb_probe_interface [ 112.017759] c0 qmi_wwan 1-2:1.6: usb_probe_interface - got id [ 112.017868] c0 qmi_wwan 1-2:1.6: not blacklisted [ 112.019348] c0 qmi_wwan 1-2:1.6: looking for a minor, starting at 176 [ 112.024117] c0 qmi_wwan 1-2:1.6: cdc-wdm3: USB WDM device [ 112.040239] c0 qmi_wwan 1-2:1.6: wwan3: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 112.040367] c0 usb 1-2: adding 1-2:1.7 (config #1, interface 7) [ 112.042019] c0 qmi_wwan 1-2:1.7: usb_probe_interface [ 112.042078] c0 qmi_wwan 1-2:1.7: usb_probe_interface - got id [ 112.042136] c0 qmi_wwan 1-2:1.7: not blacklisted [ 112.043452] c0 qmi_wwan 1-2:1.7: looking for a minor, starting at 176 [ 112.047586] c0 qmi_wwan 1-2:1.7: cdc-wdm4: USB WDM device [ 112.061555] c0 qmi_wwan 1-2:1.7: wwan4: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 112.061682] c0 usb 1-2: adding 1-2:1.8 (config #1, interface 8) [ 112.064017] c0 qmi_wwan 1-2:1.8: usb_probe_interface [ 112.064076] c0 qmi_wwan 1-2:1.8: usb_probe_interface - got id [ 112.064135] c0 qmi_wwan 1-2:1.8: not blacklisted [ 112.065718] c0 qmi_wwan 1-2:1.8: looking for a minor, starting at 176 [ 112.069625] c0 qmi_wwan 1-2:1.8: cdc-wdm5: USB WDM device [ 112.083847] c0 qmi_wwan 1-2:1.8: wwan5: register 'qmi_wwan' at usb-s5p-ehci-2, Qualcomm Gobi wwan/QMI device, 8a:67:66:e0:20:77 [ 112.520147] c0 s5p-ohci s5p-ohci: auto-stop root hub [ 112.957850] c0 usb_wwan_indat_callback: read urb received : 48 [ 112.959126] c0 usb_wwan_write: write (48 chars) [ 112.961716] c0 usb_wwan_indat_callback: read urb received : 48 [ 113.610213] c0 hub 2-0:1.0: hub_suspend [ 113.610382] c0 usb usb2: bus auto-suspend [ 113.610506] c0 s5p-ohci s5p-ohci: suspend root hub [ 114.530153] c0 mdm: check 2nd enumeration [ 114.530294] c0 pm device [ 114.530357] c0 name = mdm_hsic_pm0 [ 114.530439] c0 udev = 0x (null) [ 114.530518] c0 intf_cnt = 0 [ 114.530585] c0 block_request = false [ 114.530686] c0 mdm: silent reset!! [ 114.530792] c0 mdm_silent_reset: mdm modem has been restarted