Replicant

h1. PinePhoneBraveheartBootloader

h2. Boot log

When it was leant to me, the person lending it to me tried many distros. The last distro tried was PostMarketOS.

<pre>

U-Boot SPL 2020.01 (Jan 09 2020 - 12:17:54 +0000)

DRAM: 2048 MiB

Trying to boot from MMC1

NOTICE:  BL31: v2.1(release):v3.10.0_rc3-151-ga4b61dc7d9

NOTICE:  BL31: Built : 16:21:59, Jun 12 2019

NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)

NOTICE:  BL31: Found U-Boot DTB at 0x408e1a8, model: Pine64 LTS

NOTICE:  BL31: PMIC: Detected AXP803 on RSB.

U-Boot 2020.01 (Jan 09 2020 - 12:17:54 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)

Model: Pine64 LTS

DRAM:  2 GiB

MMC:   mmc@1c0f000: 0, mmc@1c11000: 1

Loading Environment from FAT... Unable to use mmc 1:1... In:    serial

Out:   serial

Err:   serial

Net:   phy interface7

Could not get PHY for ethernet@1c30000: addr 1

No ethernet found.

starting USB...

Bus usb@1c1a000: USB EHCI 1.00

Bus usb@1c1a400: USB OHCI 1.0

Bus usb@1c1b000: USB EHCI 1.00

Bus usb@1c1b400: USB OHCI 1.0

scanning bus usb@1c1a000 for devices... 1 USB Device(s) found

scanning bus usb@1c1a400 for devices... 1 USB Device(s) found

scanning bus usb@1c1b000 for devices... 1 USB Device(s) found

scanning bus usb@1c1b400 for devices... 1 USB Device(s) found

       scanning usb for storage devices... 0 Storage Device(s) found

Hit any key to stop autoboot:  0 

switch to partitions #0, OK

mmc0 is current device

Scanning mmc 0:1...

Found U-Boot script /boot.scr

919 bytes read in 7 ms (127.9 KiB/s)

## Executing script at 4fc00000

gpio: pin 114 (gpio 114) value is 1

Booting from SD

arch=arm

baudrate=115200

board=sunxi

board_name=sunxi

boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}

boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi

boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}

boot_net_usb_start=usb start

boot_prefixes=/ /boot/

boot_script_dhcp=boot.scr.uimg

boot_scripts=boot.scr.uimg boot.scr

boot_syslinux_conf=extlinux/extlinux.conf

boot_targets=fel mmc_auto usb0 pxe dhcp 

bootargs=init=/init.sh rw console=tty0 console=ttyS0,115200 no_console_suspend earlycon=uart,mmio32,0x01c28000 panic=10 consoleblank=0 loglevel=1 cma=256M PMOS_NO_OUTPUT_REDIRECT pmos_boot=/dev/mmcblk0p1 pmos_root=/dev/mmcblk0p2

bootcmd=run distro_bootcmd

bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00011:UNDI:003000;setenv bootp_arch 0xb;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;

bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo '(FEL boot)'; source ${fel_scriptaddr}; fi

bootcmd_mmc0=devnum=0; run mmc_boot

bootcmd_mmc1=devnum=1; run mmc_boot

bootcmd_mmc_auto=if test ${mmc_bootdev} -eq 1; then run bootcmd_mmc1; run bootcmd_mmc0; elif test ${mmc_bootdev} -eq 0; then run bootcmd_mmc0; run bootcmd_mmc1; fi

bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi

bootcmd_usb0=devnum=0; run usb_boot

bootdelay=2

bootdev=0

bootfstype=ext4

bootm_size=0xa000000

console=ttyS0,115200

cpu=armv8

devplist=1

dfu_alt_info_ram=kernel ram 0x40080000 0x1000000;fdt ram 0x4FA00000 0x100000;ramdisk ram 0x4FE00000 0x4000000

distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done

efi_dtb_prefixes=/ /dtb/ /dtb/current/

ethaddr=02:ba:83:c7:f4:f3

fdt_addr_r=0x4FA00000

fdtcontroladdr=b9f31258

fdtfile=allwinner/sun50i-a64-pine64-lts.dtb

fileaddr=4fc00000

filesize=397

kernel_addr_r=0x40080000

load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}

mmc_boot=if mmc dev ${devnum}; then devtype=mmc; run scan_dev_for_boot_part; fi

mmc_bootdev=0

partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system};

preboot=usb start

pxefile_addr_r=0x4FD00000

ramdisk_addr_r=0x4FE00000

scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;

scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done; setenv devplist

scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile

scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi

scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done

scriptaddr=0x4FC00000

serial#=92c08dba83c7f4f3

soc=sunxi

stderr=serial,vidconsole

stdin=serial,usbkbd

stdout=serial,vidconsole

usb_boot=usb start; if usb dev ${devnum}; then devtype=usb; run scan_dev_for_boot_part; fi

uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b

uuid_gpt_system=b921b045-1df0-41c3-af44-4c6f280d3fae

Environment size: 4745/131068 bytes

Loading DTB

30085 bytes read in 14 ms (2 MiB/s)

Loading Initramfs

4584216 bytes read in 220 ms (19.9 MiB/s)

Loading Kernel

15091720 bytes read in 708 ms (20.3 MiB/s)

gpio: pin 115 (gpio 115) value is 1

Resizing FDT

Booting kernel

gpio: pin 116 (gpio 116) value is 1

## Loading init Ramdisk from Legacy Image at 4fe00000 ...

   Image Name:   uInitrd

   Image Type:   AArch64 Linux RAMDisk Image (uncompressed)

   Data Size:    4584152 Bytes = 4.4 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Flattened Device Tree blob at 4fa00000

   Booting using the fdt blob at 0x4fa00000

EHCI failed to shut down host controller.

   Loading Ramdisk to 49ba0000, end 49fff2d8 ... OK

   Loading Device Tree to 0000000049b95000, end 0000000049b9ffff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]

[    0.000000] Linux version 5.4.0 (pmos@msi) (gcc version 9.2.0 (Alpine 9.2.0)) #3-postmarketos-allwinner SMP Sat Jan 18 16:55:25 UTC 2020

[    0.000000] Machine model: PinePhone

[    0.000000] earlycon: uart0 at MMIO32 0x0000000001c28000 (options '')

[    0.000000] printk: bootconsole [uart0] enabled

### postmarketOS initramfs ###

Configuring kernel firmware image search path

modprobe: module sun6i_mipi_dsi not found in modules.dep

modprobe: module sun4i_drm not found in modules.dep

modprobe: module pwm_sun4i not found in modules.dep

modprobe: module sun8i_mixer not found in modules.dep

modprobe: module ext4 not found in modules.dep

modprobe: module usb_f_rndis not found in modules.dep

NOTE: Waiting 10 seconds for the framebuffer /dev/fb0.

If your device does not have a framebuffer, disable this with:

no_framebuffer=true in <https://postmarketos.org/deviceinfo>

Setting framebuffer mode to: U:720x1440p-0

Setup usb network

  /sys/class/android_usb does not exist, skipping android_usb

  Setting up an USB gadget through configfs

Starting udhcpd

  Using interface usb0

  Start the dhcpcd daemon (forks into background)

Mount boot partition (/dev/mmcblk0p1)

Extract /boot/initramfs-postmarketos-allwinner-extra

31639 blocks

Check/repair root filesystem (/dev/mmcblk0p2)

e2fsck 1.45.5 (07-Jan-2020)

pmOS_root: recovering journal

Clearing orphaned inode 81454 (uid=10000, gid=10000, mode=0100600, size=17344)

Clearing orphaned inode 81296 (uid=10000, gid=10000, mode=0100600, size=8896)

Clearing orphaned inode 81253 (uid=10000, gid=10000, mode=0100600, size=47218)

Clearing orphaned inode 81241 (uid=10000, gid=10000, mode=0100600, size=1024)

Setting free inodes count to 27171 (was 27176)

Setting free blocks count to 81716 (was 81737)

pmOS_root: clean, 72989/100160 files, 562892/644608 blocks

Resize root filesystem (/dev/mmcblk0p2)

resize2fs 1.45.5 (07-Jan-2020)

The filesystem is already 644608 (4k) blocks long.  Nothing to do!

Mount root partition (/dev/mmcblk0p2)

umount: can't unmount /dev: Invalid argument

   OpenRC 0.42.1.6a467d4a81 is starting up Linux 5.4.0 (aarch64)

/lib/rc/sh/init.sh: line 15: can't create /dev/null: Read-only file system

 * md5sum is missing, which suggests /usr is not mounted

 * If you have separate /usr, it must be mounted by initramfs

 * If not, you should check coreutils is installed correctly

 * Mounting /proc ... [ ok ]

 * Mounting /run ... * /run/openrc: creating directory

 * /run/lock: creating directory

 * /run/lock: correcting owner

/lib/rc/sh/gendepends.sh: line 28: can't create /dev/null: Read-only file system

 * Caching service dependencies ... [ ok ]

 * Clock skew detected with `(null)'

 * Adjusting mtime of `/run/openrc/deptree' to Sat Jan 18 19:20:37 2020

 * WARNING: clock skew detected!

 * Mounting devtmpfs on /dev ... [ ok ]

 * Mounting /dev/mqueue ... [ ok ]

 * Mounting /dev/pts ... [ ok ]

 * Mounting /dev/shm ... [ ok ]

 * Mount subpartitions of /dev/mmcblk0

device-mapper: reload ioctl on mmcblk0p1  failed: Resource busy

create/reload failed on mmcblk0p1

device-mapper: reload ioctl on mmcblk0p2  failed: Resource busy

create/reload failed on mmcblk0p2

 * Mount subpartitions of /dev/mmcblk2

 * Mounting /sys ... [ ok ]

 * Mounting security filesystem ... [ ok ]

 * Mounting debug filesystem ... [ ok ]

 * Mounting config filesystem ... [ ok ]

 * Mounting persistent storage (pstore) filesystem ... [ ok ]

 * Starting udev ... [ ok ]

 * Generating a rule to create a /dev/root symlink ... [ ok ]

 * Populating /dev with existing devices through uevents ... [ ok ]

 * WARNING: clock skew detected!

 * Loading modules ... [ ok ]

 * Setting system clock using the hardware clock [UTC] ... [ ok ]

 * Setting the local clock based on last shutdown time ... [ ok ]

 * Checking local filesystems  .../dev/mmcblk2p2 is in use.

e2fsck: Cannot continue, aborting.

 * Operational error

 [ !! ]

 * Remounting root filesystem read/write ... [ ok ]

 * Remounting filesystems ... [ ok ]

 * Mounting local filesystems ... [ ok ]

 * Configuring kernel parameters ...sysctl: error: 'net.ipv4.tcp_syncookies' is an unknown key

 [ ok ]

 * Creating user login records ... [ ok ]

 * Wiping /tmp directory ... [ ok ]

 * Setting hostname ... [ ok ]

 * Starting busybox syslog ... [ ok ]

 * WARNING: clock skew detected!

 * Starting System Message Bus ... [ ok ]

 * Starting RNG Daemon ... [ ok ]

 * Could not find a wireless interface

 * Starting WPA Supplicant ... [ ok ]

 * Starting networkmanager ... [ ok ]

 * Starting chronyd ... [ ok ]

 * Enabling EG25 WWAN module ... * /run/lightdm: creating directory

 * /run/lightdm: correcting owner

 * Starting Display Manager ... [ ok ]

 * Starting oFono ... [ ok ]

 * Starting sshd ... [ ok ]

 * Activating swap file ...Configured swap file size is 0, skipping creation.

 [ ok ]

 * Starting urfkill ... [ ok ]

 * Starting local ... [ ok ]

Welcome to postmarketOS

Kernel 5.4.0 on an aarch64 (/dev/ttyS0)

pine64-pinephone login: 

</pre>