Version 6 - History - XMMProtocolInterfaces - Replicant

XMMProtocolInterfaces » History » Version 6

Denis 'GNUtoo' Carikli, 12/31/2020 02:53 AM
remove AT+ADB as it's probably not relevant for XMM modem firmwares

-Denis 'GNUtoo'  Carikli
+h1. XMMProtocolInterfaces
-Denis 'GNUtoo'  Carikli
+{{>toc}}
-Denis 'GNUtoo'  Carikli
+h2. GT-I9100
 Setup: Replicant 6.0 0004 RC3
 To get the modem UART:
 First get root in the device.
 <pre>
 root@i9300:/ # echo MODEM > /sys/devices/virtual/sec/switch/usb_sel
 </pre>
 Then unplug and replug the USB cable.
 Then some /dev/ttyACM* device appear on your laptop when you plug it again.
 <pre>
 $ ls -la /dev/ttyACM*
 crw-rw---- 1 root uucp 166, 0 31 déc.  03:34 /dev/ttyACM0
 crw-rw---- 1 root uucp 166, 1 31 déc.  03:34 /dev/ttyACM1
 crw-rw---- 1 root uucp 166, 2 31 déc.  03:34 /dev/ttyACM2
 crw-rw---- 1 root uucp 166, 3 31 déc.  03:34 /dev/ttyACM3
 crw-rw---- 1 root uucp 166, 4 31 déc.  03:34 /dev/ttyACM4
 crw-rw---- 1 root uucp 166, 5 31 déc.  03:34 /dev/ttyACM5
 crw-rw---- 1 root uucp 166, 6 31 déc.  03:34 /dev/ttyACM6
 </pre>
 <pre>
 # picocom /dev/ttyACM0
 picocom v3.1
 port is        : /dev/ttyACM0
 flowcontrol    : none
 baudrate is    : 9600
 parity is      : none
 databits are   : 8
 stopbits are   : 1
 escape is      : C-a
 local echo is  : no
 noinit is      : no
 noreset is     : no
 hangup is      : no
 nolock is      : no
 send_cmd is    : sz -vv
 receive_cmd is : rz -vv -E
 imap is        :
 omap is        :
 emap is        : crcrlf,delbs,
 logfile is     : none
 initstring     : none
 exit_after is  : not set
 exit is        : no
 Type [C-a] [C-h] to see available commands
 Terminal ready
 AT+TRACE=1
 OK
 AT+CLAC
 ATS
 ATD
 ATA
 ATO
 ATE
 ATH
 ATV
 ATZ
 ATl
 ATm
 ATQ
 ATX
 AT&F
 AT&D
 AT&C
 AT\Q
 AT+CGSMS
 AT+CMGD
 AT+CMGF
 AT+CMGL
 AT+CMGR
 AT+CMGS
 AT+CMGW
 AT+CMMS
 AT+CMSS
 AT+CNMA
 AT+CNMI
 AT+CPMS
 AT+CSCA
 AT+CSCB
 AT+CSMS
 AT+XCSSMS
 AT+XSMS
 AT+XTESM
 AT+CSDH
 AT+CSAS
 AT+CRES
 AT+CMGC
 AT+CSMP
 AT+CGREG
 AT+COPN
 AT+COPS
 AT+CREG
 AT+CSQ
 AT+XBANDSEL
 AT+XCOPS
 AT+XCSPAGING
 AT+XEONS
 AT+XREG
 AT+XAACOPS
 AT+XUBANDSEL
 AT+XRAT
 AT+CPLS
 AT+CPOL
 AT+XHOMEZR
 AT+CHUP
 AT+CMOD
 AT+CTFR
 AT+VTS
 AT+XCALLSTAT
 AT+XDTMF
 AT+XVTS
 AT+CSTA
 AT+CVHU
 AT+VTD
 AT+CCWE
 AT+CR
 AT+CRC
 AT+XPROGRESS
 AT+XREDIAL
 AT+CAOC
 AT+XLIN
 AT+CCFC
 AT+CCWA
 AT+CHLD
 AT+CLCC
 AT+CLCK
 AT+CLIP
 AT+CLIR
 AT+CNAP
 AT+COLP
 AT+COLR
 AT+CPWD
 AT+CSSN
 AT+CUSD
 AT+CCUG
 AT+CBST
 AT+CEER
 AT+CGACT
 AT+CGATT
 AT+CGAUTO
 AT+CGCLASS
 AT+CGCMOD
 AT+CGDATA
 AT+CGDCONT
 AT+CGDSCONT
 AT+CGEQMIN
 AT+CGEQNEG
 AT+CGEQREQ
 AT+CGEREP
 AT+CGPADDR
 AT+CGQMIN
 AT+CGQREQ
 AT+CGTFT
 AT+XCGCLASS
 AT+XDNS
 AT+XGAUTH
 AT+FCLASS
 AT+CRLP
 AT+XNVMPLMN
 AT+XNVMMCC
 AT+CBC
 AT+CCID
 AT+CCLK
 AT+CFUN
 AT+CGMI
 AT+CGMM
 AT+CGMR
 AT+CGSN
 AT+CIMI
 AT+CMEE
 AT+CMUX
 AT+CNUM
 AT+CPIN
 AT+CPWROFF
 AT+CRSM
 AT+CSCS
 AT+CSIM
 AT+CSVM
 AT+CTZR
 AT+CTZU
 AT+IPR
 AT+XCTMS
 AT+XGENDATA
 AT+XPINCNT
 AT+XLOG
 AT+XMER
 AT+XSIMSTATE
 AT+TRACE
 AT+XL1SET
 AT+XSIO
 AT+XDLCTEST
 AT+XPOW
 AT+XCEER
 AT+XEER
 AT+XTRACECONFIG
 AT+XMUX
 AT+XFDOR
 AT+XFDORT
 AT+XCONFIG
 AT+XAPP
 AT+XHSDUPA
 AT+CPIN2
 AT+XDATACHANNEL
 AT+CONNECTPORT
 AT+CAMM
 AT+CACM
 AT+CCHO
 AT+CCHC
 AT+XCSP
 AT+NEER
 AT+CUAD
 AT+XUICC
 AT+XLEMA
 AT+XSYSTRACE
 AT+CLAC
 AT+CPUC
 AT+CLAN
 AT+CGLA
 AT+CRLA
 AT+CPAS
 AT+XSVM
 AT+XNOTIFYDUNSTATUS
 AT+XRXDIV
 AT+XSETCAUSE
 OK
-Denis 'GNUtoo'  Carikli
+</pre>
 Denis 'GNUtoo'  Carikli
-Denis 'GNUtoo'  Carikli
+Xgoldmon seem to display things on the GT-I9100:
 <pre>
 # ./xgoldmon -vvvv -i localhost -t s2 -l /dev/ttyACM1
 LOG:>>[HIGH]oembatt.c,310,[DISP] Thermistor : measured_value=1630666778<<
 LOG:>>[HIGH]oembatt.c,137,[DISP] oem_set_batt_level : 4220<<
 LOG:>>[HIGH]oembatt.c,236,[DISP] BATT : measured_value_mv=4220, AvgBattVal_mv=4007, battery_level=5<<
 LOG:>>[LOW]oemdisplay.c,363,no change -> rssi:4, bat:5<<
 LOG:>>[HIGH]oembatt.c,310,[DISP] Thermistor : measured_value=1630666779<<
 LOG:>>[HIGH]oembatt.c,137,[DISP] oem_set_batt_level : 4225<<
 LOG:>>[HIGH]oembatt.c,236,[DISP] BATT : measured_value_mv=4225, AvgBattVal_mv=4026, battery_level=5<<
 LOG:>>[LOW]oemdisplay.c,363,no change -> rssi:4, bat:5<<
 LOG:>>[HIGH]oembatt.c,310,[DISP] Thermistor : measured_value=1630666778<<
 LOG:>>[HIGH]oembatt.c,137,[DISP] oem_set_batt_level : 4220<<
 LOG:>>[HIGH]oembatt.c,236,[DISP] BATT : measured_value_mv=4220, AvgBattVal_mv=4055, battery_level=5<<
 LOG:>>[LOW]oemdisplay.c,363,no change -> rssi:4, bat:5<<
-Denis 'GNUtoo'  Carikli
+</pre>
-Denis 'GNUtoo'  Carikli
+h2. GT-I9300
 Setup: Replicant 6.0 0004 RC3
 To get the modem UART:
 First get root in the device.
 <pre>
-Denis 'GNUtoo'  Carikli
+root@i9300:/ # echo MODEM > /sys/devices/virtual/sec/switch/usb_sel
-Denis 'GNUtoo'  Carikli
+</pre>
 Then unplug and replug the USB cable.
 Then some /dev/ttyACM* device appear on your laptop when you plug it again.
 <pre>
 $ ls -la /dev/ttyACM*
 crw-rw---- 1 root uucp 166, 0 31 déc.  03:18 /dev/ttyACM0
 crw-rw---- 1 root uucp 166, 1 31 déc.  03:18 /dev/ttyACM1
 crw-rw---- 1 root uucp 166, 2 31 déc.  03:18 /dev/ttyACM2
 crw-rw---- 1 root uucp 166, 3 31 déc.  03:18 /dev/ttyACM3
 crw-rw---- 1 root uucp 166, 4 31 déc.  03:18 /dev/ttyACM4
 crw-rw---- 1 root uucp 166, 5 31 déc.  03:18 /dev/ttyACM5
 crw-rw---- 1 root uucp 166, 6 31 déc.  03:18 /dev/ttyACM6
 </pre>
 <pre>
 # picocom /dev/ttyACM0
 picocom v3.1
 port is        : /dev/ttyACM0
 flowcontrol    : none
 baudrate is    : 9600
 parity is      : none
 databits are   : 8
 stopbits are   : 1
 escape is      : C-a
 local echo is  : no
 noinit is      : no
 noreset is     : no
 hangup is      : no
 nolock is      : no
 send_cmd is    : sz -vv
 receive_cmd is : rz -vv -E
 imap is        :
 omap is        :
 emap is        : crcrlf,delbs,
 logfile is     : none
 initstring     : none
 exit_after is  : not set
 exit is        : no
 Type [C-a] [C-h] to see available commands
 Terminal ready
 AT+TRACE=1
 OK
 AT
 OK
 AT+CLAC
 ATS
 ATD
 ATA
 ATO
 ATE
 ATH
 ATV
 ATZ
 ATl
 ATm
 ATQ
 ATX
 AT&F
 AT&D
 AT&C
 AT\Q
 AT+CGSMS
 AT+CMGD
 AT+CMGF
 AT+CMGL
 AT+CMGR
 AT+CMGS
 AT+CMGW
 AT+CMMS
 AT+CMSS
 AT+CNMA
 AT+CNMI
 AT+CPMS
 AT+CSCA
 AT+CSCB
 AT+CSMS
 AT+XCSSMS
 AT+XSMS
 AT+XTESM
 AT+CSDH
 AT+CSAS
 AT+CRES
 AT+CMGC
 AT+CSMP
 AT+CGREG
 AT+COPN
 AT+COPS
 AT+CREG
 AT+CSQ
 AT+XBANDSEL
 AT+XCOPS
 AT+XCSPAGING
 AT+XEONS
 AT+XREG
 AT+XAACOPS
 AT+XUBANDSEL
 AT+XRAT
 AT+CPLS
 AT+CPOL
 AT+XHOMEZR
 AT+XCSQ
 AT+CHUP
 AT+CMOD
 AT+CMUT
 AT+CTFR
 AT+VTS
 AT+XCALLSTAT
 AT+XDTMF
 AT+XVTS
 AT+CSTA
 AT+CVHU
 AT+VTD
 AT+CCWE
 AT+CR
 AT+CRC
 AT+XPROGRESS
 AT+XREDIAL
 AT+CAOC
 AT+XLIN
 AT+CCFC
 AT+CCWA
 AT+CHLD
 AT+CLCC
 AT+CLCK
 AT+CLIP
 AT+CLIR
 AT+CNAP
 AT+COLP
 AT+COLR
 AT+CPWD
 AT+CSSN
 AT+CUSD
 AT+CCUG
 AT+CBST
 AT+CEER
 AT+CGACT
 AT+CGANS
 AT+CGATT
 AT+CGAUTO
 AT+CGCLASS
 AT+CGCMOD
 AT+CGDATA
 AT+CGDCONT
 AT+CGDSCONT
 AT+CGEQMIN
 AT+CGEQNEG
 AT+CGEQREQ
 AT+CGEREP
 AT+CGPADDR
 AT+CGQMIN
 AT+CGQREQ
 AT+CGTFT
 AT+XCGCLASS
 AT+XDNS
 AT+XGAUTH
 AT+FCLASS
 AT+CRLP
 AT+XNVMPLMN
 AT+XNVMMCC
 AT+CBC
 AT+CCID
 AT+CCLK
 AT+CFUN
 AT+CGMI
 AT+CGMM
 AT+CGMR
 AT+CGSN
 AT+GSN
 AT+CIMI
 AT+CMEE
 AT+CMUX
 AT+CNUM
 AT+CPIN
 AT+CPWROFF
 AT+CRSM
 AT+CSCS
 AT+CSIM
 AT+CSVM
 AT+CTZR
 AT+CTZU
 AT+IPR
 AT+XCTMS
 AT+XGENDATA
 AT+XPINCNT
 AT+XLOG
 AT+XMER
 AT+XSIMSTATE
 AT+TRACE
 AT+XL1SET
 AT+XSIO
 AT+XDLCTEST
 AT+XPOW
 AT+XCEER
 AT+XEER
 AT+XTRACECONFIG
 AT+XMUX
 AT+XFDOR
 AT+XFDORT
 AT+XCONFIG
 AT+XAPP
 AT+XHSDUPA
 AT+XCAP
 AT+CPIN2
 AT+XDATACHANNEL
 AT+CONNECTPORT
 AT+CAMM
 AT+CACM
 AT+CCHO
 AT+CCHC
 AT+XCSP
 AT+NEER
 AT+CUAD
 AT+XUICC
 AT+XLEMA
 AT+XSYSTRACE
 AT+CLAC
 AT+CPUC
 AT+CLAN
 AT+CGLA
 AT+CRLA
 AT+CPAS
 AT+XSVM
 AT+XNOTIFYDUNSTATUS
 AT+XRXDIV
 AT+XRXDIV3GRAB
 AT+XMAGETKEY
 AT+XMAGETBLOCK
 AT+CPOS
 AT+CPOSR
 AT+CMOLR
 AT+CMTLR
 AT+CMTLRA
 AT+XCPOSR
 AT+XSETCAUSE
 AT+XSPEECHINFO
 OK
 </pre>

Project

General

Profile

Replicant

XMMProtocolInterfaces » History » Version 6